Lenovo ThinkSystem ST550 Setup Manual Download Page 46

Page: 46 / 136

Server model: twenty 2.5-inch SAS/SATA drives, one 8i RAID adapter, one 16i RAID adapter

Notes:

• Ensure that all cables are routed through the correct cable clips.

• Broken lines indicate the hidden parts.

Figure 22. Cable routing for server models with twenty 2.5-inch SAS/SATA drives, one 8i RAID adapter and one 16i RAID
adapter

Cable

From

SAS signal cable for

backplane 1

SAS 0 and SAS 1 connectors on
backplane 1

C0 and C1 connectors on the 16i RAID
adapter

SAS signal cable for

backplane 2

SAS 0 and SAS 1 connectors on
backplane 2

C2 and C3 connectors on the 16i RAID
adapter

Power cable for backplane 1

Power connector on backplane 1

Backplane 1 power connector on the
system board

Power cable for backplane 2

Power connector on backplane 2

Backplane 2 power connector on the
system board

ThinkSystem ST550 Setup Guide

Summary of Contents for ThinkSystem ST550









































































































































Search results

Summary of Contents for ThinkSystem ST550

Reviews:

Related manuals for ThinkSystem ST550

Brands by name

Popular brands

Lenovo ThinkSystem ST550, Setup Manual

Search results

Summary of Contents for ThinkSystem ST550

Reviews:

Related manuals for ThinkSystem ST550

Brands by name

Popular brands