Lenovo ThinkCentre M79 Hardware Maintenance Manual Download Page 140 | Manualshive

Page: 140 / 186

background image

9. Connect the new power supply assembly cables to all drives and the system board. See “Locating

parts on the system board” on page 34.

10. Lower and position the heat sink fan duct on the top of the heat sink and fan assembly until the two

screw holes in the heat sink fan duct are aligned with those in the heat sink and fan assembly. Install
the two screws to secure the heat sink fan duct.

Figure 49. Installing the heat sink fan duct

What to do next:

• To work with another piece of hardware, go to the appropriate section.

• To complete the installation or replacement, go to “Completing the parts replacement” on page 151.

Replacing the microprocessor

Attention:

Do not open your computer or attempt any repair before reading and understanding the Chapter

1 “Read this first: Important safety information” on page 1.

CAUTION:

The heat sink and microprocessor might be very hot. Turn off the computer and wait three to five
minutes to let the computer cool before removing the computer cover.

To replace the microprocessor, do the following:

1. Remove any media from the drives and turn off all attached devices and the computer. Then, disconnect

all power cords from electrical outlets and disconnect all cables that are connected to the computer.

2. Remove the computer cover. See “Removing the computer cover” on page 105.

3. Locate the system board and disconnect all cables connected to the system board. See “Locating

parts on the system board” on page 34.

4. Remove the heat sink and fan assembly with the fan duct. See “Replacing the heat sink and fan

assembly” on page 126.

Note:

Place the heat sink and fan assembly on its side so that the thermal grease on the bottom of it

does not get in contact with anything.

132

ThinkCentre M79 Hardware Maintenance Manual

«
...
138
139
140
141
142
...
»

Summary of Contents for ThinkCentre M79



























































































































































































Reviews:

No comments

Related manuals for ThinkCentre M79

Brand: Acer Pages: 4

Aspire Z5600 Series

Brand: Acer Pages: 11

Brand: Acer Pages: 17

Brand: Acer Pages: 7

Brand: IBM Pages: 2

Brand: IBM Pages: 121

Brand: Tandy Pages: 82

Brand: Igel Pages: 2

Brand: Festo Pages: 72

Brand: IBM Pages: 142

Brand: Metacentre Pages: 8

Brand: M5Stack Pages: 15

Brand: ARE Pages: 39

Brand: Gateway Pages: 346

AE1900-01SUS - Wind Top - 1 GB RAM

Brand: MSI Pages: 42

Brand: Dell Pages: 121

Brand: Dell Pages: 57

Brand: Dell Pages: 80

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands