lehman Trikes Raider XL 2014+ Installation Instructions Manual Download Page 2 | Manualshive

Page: 2 / 38

background image

2

2014+ XL Raider

PREPARING THE MOTORCYCLE

SWINGARM INSTALLATION

MOTOR MOUNT INSTALLATION

DIFFERENTIAL ASSEMBLY

BELT ALIGNMENT AND STABILIZER LINK

BRAKE SYSTEM

EXHAUST

BODY MOUNT INSTALLATION

BODY

DOOR INSTALLATION

BODY WIRING

BODY INSTALLATION

GRAB HANDLE/FINAL ASSEMBLY

STEERING NECK ADJUSTMENT

INSPECTION

TORQUE SPECIFICATIONS

BOLT BAG BREAKDOWN

© 2010. All rights reserved.

Lehman Trikes® provides this publication as is without warranty of any kind, either expressed or implied.  While every precaution has been
taken in the preparation of this manual, Lehman Trikes® assumes no responsibility for errors or omissions.  Neither is any liability assumed
for damages resulting from the use of the information contained herein.  Lehman Trikes® reserves the right to revise and improve its products
as it sees fit.  This publication describes the state of this product at the time of its publication, and may not reflect the product in the future.
Lehman Trikes® is a registered trademark.  All other brands and product names are trademarks or registered trademarks of their respective
holders.

Printed in the United States of America.

SECTION BREAKOUT

«
1
2
3
4
...
»

Summary of Contents for Raider XL 2014+







































Reviews:

No comments

Related manuals for Raider XL 2014+

Brand: B-PWR Pages: 13

Brand: hepco & becker Pages: 4

Brand: R&G Pages: 14

Brand: Yoshimura Pages: 7

Brand: BMW Motorrad Pages: 261

Brand: KTM Pages: 90

Brand: Fantic Pages: 153

Brand: Victory Pages: 323

Brand: Oxford Pages: 28

Brand: Saddlemen Pages: 2

Express Trunk Bag

Brand: Saddlemen Pages: 2

Brand: Sealey Pages: 4

Brand: FMF Pages: 4

Brand: RIEJU Pages: 152

FreeGo LTK125 2019

Brand: Yamaha Pages: 84

Brand: Yamaha Pages: 106

Brand: Yamaha Pages: 114

Brand: Yamaha Pages: 112

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands