lehman Trikes Raider XL 2014+ Installation Instructions Manual Download Page 34

Page: 34 / 38

2014+ XL Raider

NOTE: Steering head should be adjusted after

conversion is complete. Consult H-D service

manual for proper adjustment procedure.

1. Check steering to ensure it has not been previ-

ously adjusted.

See Fig. 1

. Loosen lower fork bracket pinch

bolts.

See Fig. 2

. Loosen fork stem clamp bolt located

in center of steering head.

4. Tighten fork stem bolt 1/4 turn past H-D factory

adjustment.

5. Torque fork stem clamp bolt to

35 ft. lbs

6. Torque lower fork bracket pinch bolts to

35 ft.

lbs

NOTE: Do not tighten fork bracket pinch bolts

past factory specifications. Only fork stem bolt

should be tightened past factory setting.

STEERING NECK

Stem bolt

Clamp bolt

2011+ model shown

Fig. 1

Fig. 2

Lower LH
pinch bolt

Summary of Contents for Raider XL 2014+







































Search results

Summary of Contents for Raider XL 2014+

Reviews:

Related manuals for Raider XL 2014+

Brands by name

Popular brands

lehman Trikes Raider XL 2014+, Installation Instructions Manual

Search results

Summary of Contents for Raider XL 2014+

Reviews:

Related manuals for Raider XL 2014+

Brands by name

Popular brands