lehman Trikes Raider XL 2014+ Installation Instructions Manual Download Page 38

Page: 38 / 38

2014+ XL Raider

HARDWARE

GB6403

BOLT BAG BODY/EXHAUST 04+ XL RAIDER

PART #

QTY

DESCRIPTION

CB1084

BOLT, 1/4 X 3/4 NC BUTTON HEAD SS

License plate light to bracket

CB1086

BOLT, 1/4X 1 NC BUTTON HEAD SS

Rear body mounts LH & RH

CB1161

BOLT, 5/16 X 1 GR 8 NC PLATED

Exhaust bracket (4)

CB1165

BOLT, 5/16 X 1 1/4 NC PLATED

Turn signals (2)

CB1170

BOLT, 5/16 X 1 1/2 NC PLATED

LH rear body mount (1), RH rear body mount (1) Top
support bracket (1)

CB1175

BOLT, 5/16 X 1 3/4 NC PLATED

Top body support bracket

CB1232

BOLT, 3/8 X 3/4 NC BUTTON HEAD

Exhaust support bracket

CB1416

BOLT, 1/2 X 2 1/2 NC FULL THREAD

Top body support

CB6201

U-BOLT, 1/4 x2

Top body support to frame bracket

CN3025

NUT, 1/2 NC PLATED

Top body support

CN3040

NUT, LOCK 1/4 NC PLATED

Foot pad (6), front body mount (2), rear body mount (4),
license plate bracket (2), U-bolt– top body support (2)

CN3045

NUT, LOCK 5/16 NC PLATED

Exhaust bracket (3), rear body mount brackets (2) top
body support (1)

CN3050

NUT, LOCK 3/8 NC PLATED

Exhaust support bracket

CN3070

NUT, ACORN 1/4

License plate light to bracket

CN3250-0

NUT, JAM NYLOCK 1/2 NC

Top body support

CN3400

NUT, WELL 1/4

Seat mounting

CS4031

SCREW, BH SK CAP 1/4X1.5

Front body mount

CS4080

SCREW, MACH.1/4 X 1 PAN HD PHILLIPS

Seat mounting

CW2005

WASHER, FLAT 1/4 GRADE 8

Foot pad (6), front body mount (4), rear body mount
(4), ECM mounting (2), U-bolt– top body support (2)

CW2006

WASHER, FLAT 1/4 STAINLESS STEEL

Seat mounting (1), license plate bracket to door (2),
License plate light to bracket (2)

CW2010

WASHER, FLAT 5/16 GRADE 8

LH & RH rear body bracket (4), Exhaust bracket (5),
Top body support bracket (2), turn signals (2), Top
support (2)

CW2025

WASHER, FLAT 1/2 GRADE 8

Top body support

CW2045

WASHER, LOCK 5/16 PLATED

Top body support bracket (2), turn signals (2)

CW2097

WASHER, RUBBER 5/16 x 1 1/2

Body mounting

CW2108

WASHER, FENDER 1/4 X 1 1/4 PLATED

Rear body mounting

CW2109

WASHER, FENDER 5/16 X 1 1/2 PLATED

Seat center post

CW2154

WASHER, FLAT 6.4MM X 18MM

License plate bracket (2)

FG1002

WASHER, RUBBER 1/4 x 3/4

License plate bracket (2), body mounts to trunk (4)

S001045

REFLECTOR, FENDER RED

Body- side/rear

CB1096

BOLT, 1/4X 1 1/2 NC BUTTON HEAD SS

License plate bracket to door

Summary of Contents for Raider XL 2014+







































Search results

Summary of Contents for Raider XL 2014+

Reviews:

Related manuals for Raider XL 2014+

Brands by name

Popular brands

lehman Trikes Raider XL 2014+, Installation Instructions Manual

Search results

Summary of Contents for Raider XL 2014+

Reviews:

Related manuals for Raider XL 2014+

Brands by name

Popular brands