manualshive.com logo in svg

Lauterbach AutoFocus, User Manual

Share
Download
Lauterbach AutoFocus User Manual Download Page 9

  AutoFocus User’s Guide

 

    9     

  

©1989-2018 Lauterbach GmbH

Preprocessor AutoFocus I (LA-7991)

There are two types of LA-7991, which can be distinguished with 

VERSION.HARDWARE

. 

•

The LA-7991 OTP is based on a one-time-programmable FPGA that became obsolete in 2005. 
In the 

VERSION.HARDWARE

 window it is marked with ’(OTP)’. 

•

The LA-7991 OTP is succeeded by a re-programmable version. 

Both types have a similar performance, but there is a difference in the time resolution when it comes to 
adjustment of sampling points. You might notice this in the 

Trace.ShowFocus

 window. However this should 

not impact the actual trace result. 

Before 2006 both the OTP as well as its re-programmable successor were shipped. Starting 2006 only the 
re-programmable Preprocessor with integrated termination is shipped. 

To connect the preprocessor for tracing the target hardware has to be equipped with one or two 38-pin 
MICTOR connectors. For dimensions and target connector pinout of the preprocessor refer to the chapter

 

Technical Data

. All trace signals are connected after plugging the preprocessor (TRACE A) into the target´s 

trace connector.

Preprocessors shipped before 2006 might be marked “(OTP)” in the 

VERSION.HARDWARE

 window, indicating that they are one-time-programmable. 

They support only ETM v1-3 pinouts (ARM7/9/10/11). Some CTOOLs pinouts do 
not follow the ETM v1-3 specification (e.g. OMAP1030). As a consequence, only 
simple tracing without trace compression is possible, or a new preprocessor must 
be acquired (e.g. LA-7992).

TRACE A 

TRACE B 

Summary of Contents for AutoFocus























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands