manualshive.com logo in svg

Lauterbach AutoFocus, User Manual

Share
Download
Lauterbach AutoFocus User Manual Download Page 44

  AutoFocus User’s Guide

 

    44     

  

©1989-2018 Lauterbach GmbH

Protocol Check

Detailed trace data analysis is possible, if detailed information about the trace protocol is available. The 
following are examples for the ETM.

•

ETMv1.x

•

ETMv3.x

ETMv1.x

If the basic check was completed and the trace results are still not error-free, the following procedure might 
help you determine the source of the error. By manually disassembling the captured trace data (for a single 
step), you might notice swapped pins or data channels that might have timing issues.    

To check the ETM trace signals - ETMv1.x:

1.

Run the command 

Trace.List TS PS2 PS1 PS0 TPH TPL

 to display the captured trace data in a 

Trace.List

 window:       

Electrical measurements must be done by trained personal only. Special care has 
to be taken concerning electrostatic discharge.

The target must run and the trace has to be armed during electrical measurements 
to ensure trace port activity.

ETMv1 signal

Description

TS

Trace sync signals are synchronization points for the TRACE32 
software. Invalid states will cause Harderrors and Flowerrors

Example: 16bit ETMv1.x port

Summary of Contents for AutoFocus























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands