manualshive.com logo in svg

Lauterbach AutoFocus, User Manual

Share
Download
Lauterbach AutoFocus User Manual Download Page 12

  AutoFocus User’s Guide

 

    12     

  

©1989-2018 Lauterbach GmbH

Not all termination PCBs are compatible with all AutoFocus preprocessors, so it is best to only use the 
termination PCBs that were shipped together with your preprocessor. Please refer to the table below to find 
out PCB ID combinations that are compatible. There is an ongoing effort to optimize the termination module 
for even higher frequencies, especially for the low voltage targets. In the table below, 

bold

 termination PCB 

IDs indicate that the termination PCB contains the latest improvements.

If you are unable to trace your target application at its maximum operating frequency and you do not have 
the latest available termination module, contact [email protected] for delivery arrangements. Use the 
PowerTrace-AF Diagnosis tool to find out your preprocessors PCB IDs. (See  

Access the Diagnosis Tool

.)       

Preprocessor AutoFocus II (LA-7992)

The AutoFocus preprocessor II is the next generation of AutoFocus preprocessors. Its handling is similar to 

 

ARM-ETM AutoFocus (LA-7991)

.

LA-7991 PCB ID

Termination PCB ID for 1.8 … 3.3 V

Termination PCB ID for 1.8 … 5 V

0x0 (OTP)

0x4

0x1

0x7 (OTP)

0x4

0x1

0xE (OTP)

0x6, 0xE, 

0xF

0x2

0x0

0xF

0x2

0x1

0xF (integrated)

not applicable

Not all termination PCBs are compatible with all AutoFocus preprocessors, so it 
is best to only use the termination PCBs that were shipped together with your 
preprocessor.
You must not use the low-voltage termination for target voltages above 3.3 V

Summary of Contents for AutoFocus























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands