Lauterbach AutoFocus User Manual Download Page 27

Page: 27 / 86

AutoFocus User’s Guide

Searching for Errors

TRACE32 uploads only the requested trace information to the host to provide a quick display of the trace
information. Consequently, errors that are out of the uploaded range are not immediately visible.

There are several ways to search for errors within the trace, all of them will force TRACE32 to upload the
complete trace information to the host:

The

Trace Find

dialog:

In the

Trace.List

window, click

Find

to open a dialog with special search options:

Select

Expert

and enter “flowerror” in the

items

field. The item entry is not case sensitive.

Use the

Find First

and

Find

Next

buttons to jump to the next flowerror within the trace.

Click

Find All

to open a window listing all flowerrors.

The command

Trace.FindAll , FLOWERROR

This command searches for

errors

within the entire trace buffer. The records are listed in a window.

The command corresponds to

Find All

described above.

Summary of Contents for AutoFocus























































































Search results

Summary of Contents for AutoFocus

Reviews:

Brands by name

Popular brands

Lauterbach AutoFocus, User Manual

Search results

Summary of Contents for AutoFocus

Reviews:

Brands by name

Popular brands