manualshive.com logo in svg

Lauterbach AutoFocus, User Manual

Share
Download
Lauterbach AutoFocus User Manual Download Page 84

  AutoFocus User’s Guide

 

    84     

  

©1989-2018 Lauterbach GmbH

LA-7921   

PP-ARM-ETM/200      

Preprocessor for ARM-ETM 200 flex cable

Preprocessor for ARM7/ARM9/ARM10/ARM11/Cortex
Embedded Trace Macrocell (ETM),
Program Trace Macrocell (PTM),
connector cable and software,
200 MHz clock speed (200 Mbps), 4 x Trace-Depth,
0.9 to 3.6V
support normal mode, 4 bit DeMux mode,
normal halfrate mode, Mux mode and
4 bit DeMux halfrate mode
support max. 16 bit trace port size
Important: 3ns setup time, 1ns hold time needed
ETMV3.x Continuous Mode only without idle-filter
flex extension for Mictor 38pin connector
for target connection included

LA-7991   

PP-ARM-ETM-AF       

Preprocessor for ARM-ETM with AUTOFOCUS Flex

Preprocessor for ARM7/ARM9/ARM10/ARM11/Cortex
Embedded Trace Macrocell (ETM),
Program Trace Macrocell (PTM),
Connector cable and software,
350 MHz clock speed, 4 x Trace-Depth,
Variable threshold level and termination voltage,
AUTOFOCUS self calibration technology,
Support all ETM modes, with 2 MICTOR connectors,
Supports 1.8 to 3.3V - else contact support
Requires PowerTrace/Ethernet Version 6 or higher
or PowerTrace II
Support max. 32 bit trace port size for ARM11
1 flex extension for Mictor 38pin connector
for target connection included

LA-7925   

DUAL-2SINGLE-ETM-H  

Converter Dual-ETM to 2 single ETMs Horizon.

Converter Dual-ETM to 2 single ETMs
horizontal
for the use with 2 Preprocessor for
ARM-ETM Halfrate (LA-7921)

LA-7926   

DUAL-2SINGLE-ETM-V  

Converter Dual-ETM to 2 single ETMs Vertical

Converter Dual-ETM to 2 single ETMs
vertical
for the use with 2 Preprocessor for ARM-ETM
(LA-7889)

LA-7922   

CONVERTER-VOLT-ETM  

Converter 5V to 3.3V for ARM-ETM

Converter to connect 5V targets to preprocessor
for ARM-ETM

LA-3818   

CONV-MIC+JTAG-MIPI60

ARM Converter 2x Mictor-38, ARM-20 to MIPI-60

Converter to connect an ARM ETM Preprocessor with one
or two Mictor-38 connectors (32-bit ETMv3) and an ARM
Debug Cable to a MIPI-60 connector on the target.

LA-3809   

CONV-ARM-MIC/MIPI   

Converter Mictor-38 to MIPI-20/34

Converter to connect an ARM Preprocessor to a 20 pin
connector specified by MIPI and CoreSight. It allows
to use the Preprocessor on the 4 bit wide trace port
of the MIPI-20 connector. This converter can be
re-configured for the MIPI-34 connector.

LA-3816   

CON-2XMICTOR-MIPI60 

Converter 2x Mictor-38 to MIPI-60

Converter to connect an ARM Preprocessor to a
MIPI-60 on the target. Suitable for up to 16-bit
ETMv3. The converter is prepared to support various
other configurations because all clock and data
signals of the MIPI-60 are connected to the
Preprocessor.

LA-3817   

CON-MIPI60-MICTOR38 

Converter MIPI-60 to Mictor-38 (ETMv3 Pinout)

Converter to connect a Preprocessor with MIPI-60
connector to a Mictor-38 connector on the target
assuming an ETMv3 pinout up to 16 bit.

OrderNo  Code

Text

Summary of Contents for AutoFocus























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands