Lauterbach AutoFocus User Manual Download | Manualshive

Page: 35 / 86

background image

AutoFocus User’s Guide

35

©1989-2018 Lauterbach GmbH

8. Check

Check the version of your PowerTrace I module. Version 6 is required for targets running faster than
200 MHz (

VERSION.HARDWARE2

).

9. Check

Check the preprocessor seen by the TRACE32 software.

VERSION.HARDWARE

shows all detected

hardware.

10. Check

In case of preprocessors with more than one Mictor connector, double-check that the Mictor connectors are
properly connected to your target. For trace port sizes <= 16 bit, TRACE B remains unconnected. For further
information on the correct connection of TRACE A / TRACE B, refer to

Dimensions

.

11. Check

Check the trace port pinout.

Did your target board work with other PowerTrace/Preprocessor combinations? If your target worked with
other PowerTrace/preprocessor combinations, your trace port pinout can be assumed to be correct. This is
not always true for TPAs from other vendors. Lauterbach tools assume that the trace port pinout follows
exactly the trace specification of the used architecture (please refer to

Connector Layout

).

Has to be 06-00 or higher

Detected preprocessor hardware
must show AutoFocus!

«
...
33
34
35
36
37
...
»

Summary of Contents for AutoFocus























































































Reviews:

No comments

Related manuals for AutoFocus

Brand: Rangevision Pages: 31

Brand: Pall Pages: 51

Brand: ZAMST Pages: 21

Brand: UNIA Pages: 62

Brand: R2 Pages: 20

Brand: ParaBody Pages: 5

Brand: Baileigh Industrial Pages: 28

Brand: Baileigh Industrial Pages: 56

Brand: MAGIC FX Pages: 25

Brand: L-Acoustics Pages: 5

Brand: GE Pages: 18

Brand: uniprox Pages: 3

Brand: ABB Pages: 4

WELCH LVS 600 T

Brand: Gardner Denver Pages: 68

Brand: BRAND Pages: 21

Brand: Milestone Pages: 40

Firefly 808 Universal

Brand: Phonic Pages: 27

Brand: Ametek Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands