Lauterbach AutoFocus User Manual Download

Page: 31 / 86

AutoFocus User’s Guide

Access the Diagnosis Tool

Lauterbach provides a diagnosis tool for the

Preprocessor with AUTOFOCUS

. It is recommended that you

add the

AF Diagnosis

button to the TRACE32 toolbar for quick access to the diagnosis tool.

To access the diagnosis tool via a toolbar button:

Add this script line to the PRACTICE script file system-settings.cmm in your TRACE32 system
directory:

Re-start TRACE32.

The

AF Diagnosis

button is now available on the TRACE32 toolbar.

To just start the diagnosis tool, execute the following command:

If there is no AutoFocus preprocessor attached, executing this script will generate an error message.
Otherwise, it displays some diagnosis results in the following window:

Do not feel discouraged if some of the diagnosis results displayed in the window are meaningless to you.
Instead follow the steps in section

Diagnosis Check List

DO ~~/demo/etc/diagnosis/autofocus/add_afdiag_button.cmm

DO ~~/demo/etc/diagnosis/autofocus/afdiagnosis.cmm

Info

button

Summary of Contents for AutoFocus























































































Search results

Summary of Contents for AutoFocus

Reviews:

Related manuals for AutoFocus

Brands by name

Popular brands

Lauterbach AutoFocus, User Manual

Search results

Summary of Contents for AutoFocus

Reviews:

Related manuals for AutoFocus

Brands by name

Popular brands