manualshive.com logo in svg

Lauterbach AutoFocus, User Manual

Share
Download
Lauterbach AutoFocus User Manual Download Page 10

  AutoFocus User’s Guide

 

    10     

  

©1989-2018 Lauterbach GmbH

Use a Mictor Flex Extension to connect the preprocessor with the trace target connector. Let the second 
connector (TRACE B) unused, if the target does not support >16bit trace ports.

There are two different ways to connect the debug cable:

•

using the JTAG connector of your target platform

•

using the JTAG connector of the preprocessor 

The JTAG connector of the preprocessor is a 20-pin connector. The connector is located under the blue flat 
cable connectors and conforms to ARM’s 20-in debug connector. If you are using a 14-pin debug cable you 
need to use a 

JTAG ARM Converter 14-20 (LA-7747)

. Other architectures require an converter or must 

use a separate connector on the target.

 

For ARM architectures mostly the debug connector of the preprocessor is the 
better choice, if both connectors are available on the target hardware.
Bad JTAG communication using the targets debug connector is caused by 
extending the JTAG lines by the preprocessor.

AutoFocus I

AutoFocus II

Summary of Contents for AutoFocus























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands