Lauterbach AutoFocus User Manual Download

Page: 34 / 86

AutoFocus User’s Guide

6. Check

Execute

Trace.AutoFocus

and both an automatic hardware configuration as well as the trace test

described above will be executed. For frequency-scaling targets, multiple scans may be necessary to check
the correct sampling points.

7. Check

Check the trace port data rate. Depending on the trace macrocell, the data rate of the trace port could be
coupled on the core clock frequency or not. E.g.:

ETMv1/2: Bw=fcore * 1bit/ch

ETMv3: Bw=fport * 2bit/ch

; Example: extended trace test

; a) Hardware configuration and trace test

Trace.AutoFocus

; b) Extended trace test

; Accumulate data eye information (10 runs)

RePeaT 10.

(

Trace.TestFocus /Accumulate

)

; c) Show results

Trace.ShowFocus

Product Number

Datarate (Bw)

PowerTrace
LA-7690,
LA-7707

<320Mbaud/s

PowerTrace II
LA-7692,
LA-7693,
LA-7694

800Mbaud/s

Summary of Contents for AutoFocus























































































Search results

Summary of Contents for AutoFocus

Reviews:

Related manuals for AutoFocus

Brands by name

Popular brands

Lauterbach AutoFocus, User Manual

Search results

Summary of Contents for AutoFocus

Reviews:

Related manuals for AutoFocus

Brands by name

Popular brands