manualshive.com logo in svg

Lauterbach AutoFocus, User Manual

Share
Download
Lauterbach AutoFocus User Manual Download Page 55

  AutoFocus User’s Guide

 

    55     

  

©1989-2018 Lauterbach GmbH

The correlation between 

Analyzer.ShowFocusEye

 and 

Analyzer.ShowFocusClockEye

 is shown with the 

following 3D-figure: 

On the lower part of the figure, different data eye scans are cascaded. The data threshold level and the 
sampling point are marked by black lines. The data threshold line also defines the level where the clock eye 
picture would be normally placed within this graph.

Summary:

The clock eye scan shows a third dimension of multiple data eye scans.     

•

The scan of 

Analyzer.ShowFocusEye

 keeps the clock threshold constant while

the data threshold is changed.

•

The scan of 

Analyzer.ShowFocusClockEye

 keeps the data threshold constant while

the clock threshold is changed.

Different data eye scans of 

Analyzer.ShowFocusEye

Clock eye scan of 

Analyzer.ShowFocusClockEye

Data threshold level

Summary of Contents for AutoFocus























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands