Lattice Semiconductor ECP5 Versa Technical Notes Download

Page: 34 / 78

ECP5 and ECP5-5G Hi

h-Speed I/O Interface

Figure 32. DDR2, DDR3/DDR3L, LPDDR2 and LPDDR3 Write Side (DQ, DQS and DM)

This interface uses the following modules:

• ODDRX2DQA to generate the data DQ and DM signals. TSHX2DQA is used to generate the tristate control for

the DQ output

• ODDRX2DQSB to generate DQS output. TSHX2DQSA is used to generate the DQS tristate control.

• DQSW270 which is the 270 degree delayed DQS signal is used to generate the DQ and DM outputs

• DQSW is 90 degrees shifted from the DQSW270 is used to generate DQS output

• The DQSW270 and DQSW clocks are generated in the DQSBUFM module shown on the Read side Implemen-

tation figure.

• When write leveling is enabled, the dynamic delay for write leveling (DYNDELAY[7:0]) is applied both to DQSW

and DQSW270 so that the DQ and DQS phase relationship is maintained.

• ECLK and SCLK are used inside the ODDRX2 module before data is transferred to the DQSW270 and DQSW

clocks. The ECLK is generated by the EHXPLLL module and the SCLK is generated by the CLKDIVF module,
both shown in the Read side implementation.

* Figure 32 shows one tristate. The software generates one tristate element for each DQ port

DDR_reset

dqs_0

dq_0(0)

dq_0(7)

dm_0

Eclk (from ECLKSYNCA as shown in the Input interface)

Sclk (from CLKDIVF as shown in the Input interface)

DQSW270 (from DQSBUFM as shown in the Input interface)

DQSW (from DQSBUFM as shown in the Input interface)

dqtri_0(0)

dataout_0(8)
dataout_0(0)

dataout_0(16)
dataout_0(24)

dataout_0(15)

dataout_0(7)

dataout_0(23)
dataout_0(31)

1'b0

dqso_0(0)

1'b0

dqso_0(1)

dqstri_0(0)
dqstri_0(1)

D0
D1
D2
D1
RST
DQSW270
SCLK
ECLK

RST
D0
D1
D2
D3
SCLK
ECLK
DQSW

ODDRX2DQA

ODDRX2DQSB

T0
T1
SCLK
ECLK
DQSW
RST

TSHX2DQSA

D0
D1
D2
D1
RST
DQSW270
SCLK
ECLK

datamask_0(0)
datamask_0(1)
datamask_0(2)
datamask_0(3)

D0
D1
D2
D1
RST
DQSW270
SCLK
ECLK

ODDRX2DQA

T0
T1

SCLK
ECLK
DQSW270
RST

TSHX2DQA

ODDRX2DQA

Summary of Contents for ECP5 Versa















































































Search results

Summary of Contents for ECP5 Versa

Reviews:

Related manuals for ECP5 Versa

Brands by name

Popular brands

Lattice Semiconductor ECP5 Versa, Technical Notes

Search results

Summary of Contents for ECP5 Versa

Reviews:

Related manuals for ECP5 Versa

Brands by name

Popular brands