Lattice Semiconductor ECP5 Versa Technical Notes Download Page 15 | Manualshive

Page: 15 / 78

Lattice Semiconductor ECP5 Versa Technical Notes Download Page 15

15

ECP5 and ECP5-5G Hi

g

h-Speed I/O Interface

GDDRX2_TX.ECLK.Ali

g

ned

The interface is used to generate Generic Transmit DDR with 2X gearing using high speed edge clock (ECLK). The
Clock output is edge aligned to the Data output.

This DDR interface uses the following modules:

• ODDRX2Ffor 2X gearing is used to generate the output data

• The high speed ECLK is routed to the edge clock tree through the ECLKSYNCB module

• The SCLK is routed on the primary clock tree and is generated from the ECLK using the CLKDIVF module

• The same ECLK and SCLK are used for both Data and Clock generation.

• The startup synchronization soft IP (GDDRX_SYNC) is required for this interface to tolerate the skew between

the ECLKSYNCB Stop input and the Reset to the DDR and CLKDIV modules.

• The ECLKBRIDGE can be optionally enabled if the data bus will be crossing over between the left and right sides

of the device. If ECLKBRIDGE is enabled then the ECLKBRIDGECS element should be used in the interface
before the ECLKSYNCB element. This element can be enabled through Clarity Designer.

• Optionally the user can choose to use the DELAYG or DELAYF element to delay the data output

• The output data can be optionally tristated using either a Tristate input going through an I/O register.

Figure 16. GDDRX2_TX.ECLK.Aligned Interface

Interface Requirements

• The SCLK input to the output DDR modules must be routed on the primary clock tree and the ECLK input is

routed on the edge clock tree

• “USE PRIMARY” preference may be assigned to the SCLK net

• The user must set the timing preferences as per section “Timing Analysis Requirement”

GDDRX2_TX.ECLK.Centered

This interface is used to implement Generic Transmit DDR with 2X gearing using edge clock (ECLK). The Clock
output is centered to the Data output.

This DDR interface uses the following modules:

• ODDRX2F for X2 gearing is used to generate the data output

• The high speed ECLK is routed to the edge clock tree through the ECLKSYNCB module

• The SCLK is routed on the primary clock tree and is generated from the ECLK using the CLKDIVF module

D[3:0]

SCLK

RST

Q

Data [3/ 7/ 9:0]

SCLK

RST

Q

4'b0101

Refclk

Dout

Clkout

ECLK

ECLKI

STOP

ECLKO

CLKDIVF

CLKI

RST

ALIGNWD

CDIVX

ECLK

ODDRX2F

Edge

Primary

Sclk

1'b 0

ECLKSYNCB

sync_reset

GDDR_SYNC

Sync_clk

Start

RST

START

SYNC_CLK

DDR_RESET

STOP

READY

Ready

D[3:0]

ODDRX2F

«
...
13
14
15
16
17
...
»

Summary of Contents for ECP5 Versa















































































Reviews:

No comments