Lattice Semiconductor ECP5 Versa Technical Notes Download Page 17 | Manualshive

Page: 17 / 78

Lattice Semiconductor ECP5 Versa Technical Notes Download Page 17

17

ECP5 and ECP5-5G Hi

g

h-Speed I/O Interface

Figure 18. GDDRX71_TX.ECLK Interface

Interface Requirements

• The SCLK input to the output DDR modules must be routed on the primary clock tree and the ECLK input is

routed on the edge clock tree

• “USE PRIMARY” preference may be assigned to the SCLK net

• The user must set the timing preferences as per section “Timing Analysis Requirement”

Generic DDR Desi

g

n Guidelines

This section describes the various design guidelines used for building generic high speed DDR interfaces in ECP5
and ECP5-5G devices. In additional to these guidelines, it is also required to follow the Interface Rules described
for each type of interface, you will need to find the interface you are building in the section above “High Speed Inter-
face Details”.

Usin

g

the Hi

g

h Speed Ed

g

e Clock Brid

g

e

The High Speed Edge Clock Bridge is available to wide data busses to bridge the edge clock from one side to the
other. To enable this bridge the user would need to instantiate the “ECLKBRIDGECS” element in the HDL design.
When using the ECLKBRIDGE, both the ECLK1 or ECLK0 on that side (spanning both the banks will be used).
This will reduce the number of interfaces that can be built on a given side. See TN1263,

ECP5 and ECP5-5G sys-

Clock PLL/DLL Design and Usage Guide

for details.

Receive Interface Guidelines

• Differential DDR interface can be implemented on the Left and Right sides of the device

• There are 4 different edge clocks available per side (two per bank).

• Each of the edge clocks can be used to generate either a centered of aligned interface.

• Each side has two CLKDIV modules which would mean you can implement two different GDDRX2 RX interface

per side since each 2X gearing would require CLKDIV module to generate a slower SCLK.

• There is DDRDLLA located on each corner of the device, total of 4 in a device. LLC and LRC DDRDLLs only

drive code to one side whereas the ULC and URC DDRDLLs drive code to two sides turning corners

• Each DQSBUF/DLLDEL has access to two DDRDLLs hence two different RX rates are available per side, 4 are

available on the entire device.

• The Receive clock input should be placed on a dedicated PCLK input pin. The PCLK pin has direct access to the

edge clock tree for centered interface and it also has direct connection to the DLLDELD when implementing an
aligned interface.

• When implementing IDDRX71 interface, the complementary PAD is not available for other functions since the

IDDRX71 used the I/O registers of the complementary PAD as well.

SCLK

RST

Q

ODDRX71B

Data0 [6:0]

SCLK

RST

Q

7'b1100011

Dout

Clkout

ECLK

ECLKI

STOP

ECLKO

CLKDIVF

CLKI

RST

ALIGNWD

CDIVX

D[6:0]

ECLK

(divby 3.5)

Edge

Primary

Sclk

Refclk

D[6:0]

ECLKSYNCB

“0”

sync_reset

GDDR_SYNC

Sync_clk

Start

RST

START

SYNC_CLK

DDR_RESET

STOP

READY

Ready

ODDRX71B

«
...
15
16
17
18
19
...
»

Summary of Contents for ECP5 Versa















































































Reviews:

No comments