![background image](http://html1.mh-extra.com/html/land-pride/pfs4000/pfs4000_operators-manual_3508961032.webp)
Section 6: Options & Accessories
PFS4000, PFS5060 & PFS8010 Pendulum Spreaders 309-124M
11/20/20
28
Section 6: Options & Accessories
PFS5060 Hydraulic Gate Kit
309-126A
HYDRAULIC OPENING SYSTEM
Refer to Figure 6-1:
1. Remove nut (#3) from drive unit stud (#2).
2. Attach mounting bracket (#1) to stud (#2) with
existing nut (#3). Tighten nut to the correct torque.
Hydraulic Gate Kit And Assembly & Set-Up
Figure 6-1
3. Insert bushing (#7) into mounting hole in base of
hydraulic cylinder (#4).
4. Attach hydraulic cylinder (#4) to cylinder mounting
bracket (#1) with M8 x 30 (1 3/16") bolt (#5), flat
washers (#6), and self locking nut (#8). Tighten self
locking nut to the correct torque.
5. Insert M12 x 60 (2 3/8") hex head bolt (#10) through
end hole in hydraulic cylinder rod (#4) and screw jam
nut (#11) part way onto bolt (#10).
6. Insert bolt (#10) into bottom hole in lever arm (#9)
and screw self locking nut (#12) onto bolt (#10) until
nut has full thread engagement. Tighten jam
nut (#11) against lever arm.
7.
Attach hydraulic hose (#14) to double acting
hydraulic cylinder (#4). Rotate elbow end of hose up
45
o
and tighten elbow to hydraulic cylinder port.
8. Wrap hydraulic hose around main frame as needed
to keep hose out of driveline and cylinder pinch
points. Attach coupling end of hydraulic hose to
tractor duplex outlet.
30837
PFS8010 Hydraulic Gate Kit
309-130A
HYDRAULIC OPENING SYSTEM
Refer to Figure 6-2:
1. Bolt adjusting bracket (#13) to cylinder mounting
bracket (#14) with M8 x 20 (7/8") hex socket flat head
screws (#1A & #1B), flat washers (#15) and self
locking nuts (#16). Draw nuts up snug, do not tighten.
2. Remove nut (#3) from drive unit stud (#2).
3. Attach mounting bracket (#14) to stud (#2) with
existing nut (#3). Tighten nut the correct toque.
Hydraulic Gate Kit And Assembly & Set-Up
Figure 6-2
4. Insert bushing (#7) into mounting hole in base of
hydraulic cylinder (#4).
5. Attach hydraulic cylinder rod (#4) to bracket (#13)
with M8 x 30 (1 3/16") bolt (#5), flat washers (#6), and
self locking nut (#8) as shown. Tighten self locking
nut to the correct torque.
6. Loosen compression spring nut (#18) until lever (#9)
moves freely.
7.
Insert M12 x 60 (2 3/8") hex head bolt (#10) through
end hole in hydraulic cylinder rod (#4) and screw
jamb nut (#11) part way onto bolt (#10).
8. Insert bolt (#10) into bottom hole in lever arm (#9)
and screw self locking nut (#12) onto bolt (#10) until
nut has full thread engagement. Tighten jamb
nut (#11) against lever arm.
9. Attach hydraulic hose (#17) to double acting
hydraulic cylinder (#4). Rotate elbow end of hose up
35
o
and tighten elbow to hydraulic cylinder port.
10. Wrap hydraulic hose around main frame as needed
to keep hose out of driveline and cylinder pinch
points. Attach coupling end of hydraulic hose to
tractor duplex outlet.
30781