background image

Section 12: Troubleshooting 

PFS4000, PFS5060 & PFS8010 Pendulum Spreaders 309-124M

11/20/20

51

Table of Contents

Troubleshooting Chart

Problem

Cause

Solution

Field Skips

Not traveling parallel to the preceding pass 
at half the spread width away from the 
pass. 

Travel parallel to the preceding pass at half 
the spread width away from the pass with 
slight overlapping of each pass.

Set spreader to disperse product at half the 
rate and go over the field plot twice using a 
2nd pattern that crosses the first pattern.

Wind is blowing the product around.

Spread product on a calm non-windy day.

Spread width not suitable

Pendulum swing not adjusted correctly.

Readjust Pendulum swing.

Wind is blowing product around.

Spread product on a calm non-windy day.

Incorrect working height.

Adjust 3-point so that end of pendulum is 
29 1/2" above the ground.

Hopper & pendulum is not parallel to the 
ground.

Adjust 3-point lower arms and center link to 
level hopper parallel with ground.

Effective spread pattern not 
correct

Incorrect pendulum attached to spreader.

Change pendulums.

Travel speed is incorrect.

Set tractor power take-off speed to 540. 
Power take-off speed can be slowed a little 
to disperse product at a smaller width.

Pendulum is worn, cracked or broken.

Replace pendulum.

Uneven distribution of product

Roughness of terrain.

Slow down and decrease gate openings.

Wind is blowing product around.

Spread product on a calm non-windy day.

Product won’t discharge out of 
end of pendulum properly

Product is too wet or humid.

Use dry product only.

Excessive fertilizer lumps, product 
particulates are larger than normal or 
foreign body in product.

Clean product or replace product.

Hopper exits are clogged.

Clean hopper exits.

Pendulum is plugged.

Clean pendulum.

Discharge gate won’t open.

Check gate operation for obstructions. 
Clean obstructions from gate operation.

Check gate mechanics for bent or broken 
parts. Repair or replace parts.

Pendulum spout is worn, cracked or 
broken.

Replace pendulum spout.

Deflector on end of pendulum spout is 
worn, cracked or broken.

Replace pendulum spout.

Spreader Chart is inconsistent 
with actual discharge rate

Varying product size, specific gravity, 
treatment, moisture content, inert material 
in product, lumps, different mixtures and 
roughness of terrain can cause the chart to 
be inconsistent.

Make adjustments to adjust nut on the 
regulation bar and to tractor gear speed to 
achieve desired discharge rate. Refer to 
“Set Hopper Discharge Rate” on page 35.

Section 12: Troubleshooting

Summary of Contents for PFS4000



























































Reviews: