manualshive.com logo in svg

Land Pride PFS4000, Operator'S Manual

Share
Download
Land Pride PFS4000 Operator'S Manual Download Page 18

Section 1: Drive Unit Assembly 

PFS4000, PFS5060 & PFS8010 Pendulum Spreaders 309-124M

11/20/20

14

Table of Contents

Tractor Requirements

WARNING

!

To avoid serious injury or death:  

Lightweight tractors with rear attached implements may need 

weights added to the front to maintain steering control. 

Consult your tractor Operator’s Manual to determine proper 

weight requirements and maximum weight limitations.

Minimum Horsepower

1

   . . . . . . . . . . . . . . . . . . . .6 hp

Minimum Tractor Weight . . . . . . .  See Warning Above
3- Point Hitch Type:

PFS4000   . . . . . . . . . . . . . . . . . . . . . . . . . . . . Cat. I

PFS5060   . . Cat. I inside & Cat. II outside the frame

PFS8010   . . . . . . . . . . . . . . . . . . . . . . . . . . .  Cat. II

Rear Power Take-Off Speed   . . . . . . . . . . . .  540 rpm
Power Take-Off Shaft Type . . . . . . . . .  1 3/8”-6 Spline
Hydraulic Outlet

2

  . . . . . . . . . . . . . . . . . . Single Outlet

Notes:

1

 Horsepower required to power the drive unit only.

2

 Required for optional PFS5060 & PFS8010 

Hydraulic Gate Kit only.

Assembly & Set-Up

This Pendulum Spreader will require some assembly 

before the unit can be attach to the customer’s tractor. 

Read and understand this Operator’s Manual before 

assembling the spreader. An understanding of how the 

unit works will aid in the assembly and setup. 

Torque Requirements

Refer to “Torque Values Chart for Common Bolt Sizes” on 

page 52 to determine correct torque values when 

tightening hardware.

Pendulum Flange Assembly

Refer to Figure 1-1:

1. Apply blue loctite (not permanent loctite) to 

M12-10.9 x 65 (2 1/2") bolts (#4). Loctite to be 

supplied by the customer.

2. Attach flange (#2) to drive unit flange (#1) with 

M12-10.9 x 65 (2 1/2") bolts (#4), flat washers (#3) 

and special square nuts (#5). Screw bolts onto nuts 

only 3 or 4 complete 360

o

 turns. Do not tighten at this 

time.

Pendulum Flange Assembly

Figure 1-1

Pendulum Spout Assembly

Refer to Figure 1-2:

1. Rotate pendulum spout (#1) 90 degrees 

counterclockwise and insert into flange opening (#2).

2. Rotate pendulum spout 90 degrees clockwise to 

upright position. Verify spout is properly seated and 

then tighten bolts (#3) to the correct torque.

30778

Special Square Nut

Apply blue loctite to bolt threads

Section 1: Drive Unit Assembly

Pendulum Assembly (Upright Rotation Shown)

Figure 1-2

30779

Summary of Contents for PFS4000



























































Reviews:

No comments

Brands by name

Popular brands

Load more brands