La Marzocco Linea PB Operating Manual Download Page 7

Page: 7 / 64

3. Installation

Fig. 2 - Installation Guide

Fig. 3 - Installation Nomenclature

WARNING

THIS APPLIANCE IS NOT INTENDED FOR USE BY PER-

SONS (INCLUDING CHILDREN) WITH REDUCED PHYSI-

CAL, SENSORY OR MENTAL CAPABILITIES, OR WITH

LACK OF EXPERIENCE AND KNOWLEDGE, UNLESS

THEY HAVE BEEN GIVEN SUPERVISION OR INSTRUC-

TION CONCERNING THE USE OF THE APPLIANCE BY A

PERSON RESPONSIBLE FOR THEIR SAFETY.

WARNING

THE COFFEE BOILER AND STEAM BOILER CONTAIN

WATER AT ELEVATED TEMPERATURE. WATER TEM-

PERATURE OVER 125°F / 52°C CAN CAUSE SEVERE

BURNS INSTANTLY OR DEATH FROM SCALDING (COF-

FEE BOILER 207°F/97°C-STEAM BOILER 256°F /124°C)

WARNING

THE MACHINE IS INTENDED TO

BE PERMANENTLY CONNECTED

TO FIXED WIRING, AND IT IS

ADVISABLE THAT A RESIDUAL

CURRENT DEVICE (RCD) WITH A

RATED RESIDUAL OPERATING

CURRENT NOT EXCEEDING 30 mA

IS INSTALLED.

Drain Hose Connection

Expansion Valve

Drain Grate

Drain Tray

Water Hose

Underneath Base

of the Frame

LA FIGURA AFFIANCO DESCRIVE COME

COLLEGARE OGNI FILO ALLA SPINA.

RISPETTARE ANCHE LE NORME FEDERALI,

STATALI O LOCALI VIGENTI.

MODELLO/SERIE GRUPPO

V/Hz

POTENZA

NOMINALE

(W)

INPUT

NOMINALE

(A)

POTENZA

CALDAIA

CAFFE’

POTENZA

CALDAIA

VAPORE

POTENZA

TOTALE

DIMENSIONE CAVO

ALIMENTAZIONE

ELETTRICA (mm²)

LINEA PB

2GR

AC220V/60Hz

AC208-240/60Hz

AC380/50Hz

4600

20-22

1400

3000

4400

PER DETTAGLI

3GR

6100

1900

4000

5900

VEDERE I

COLLEGAMENTI

ELETTRICI

4GR

8000

2800

5000

7800

3 X FILI

NEUTRO

FASE

TERRA

1 X GIALLO & VERDE

1 X BLU
1 X MARRONE

CAVO ALIMENTAZIONE ELETTRICA:

ATTENZIONE

AC220V/60Hz

AC208-240/60Hz

AC380/50Hz

AC220V/60Hz

AC208-240/60Hz

AC380/50Hz

25-29

30,5

33-39

THE DETAILS ON THE LEFT DESCRIBE

HOW TO CONNECT EACH WIRE TO THE PLUG.

RESPECT ALSO THE LOCAL SAFETY

REGULATIONS.

MODEL/SERIES

GROUP

V/Hz

RATED

POWER

(W)

RATED

INPUT

(A)

COFFEE

BOILER

WATTAGE

STEAM

BOILER

WATTAGE

TOTAL

WATTAGE

POWER CORD

SIZE (mm²)

LINEA PB

2GR

AC220V/60Hz

AC208-240/60Hz

AC380/50Hz

4600

20-22

1400

3000

4400

SEE ELECTRICAL

3GR

6100

1900

4000

5900

CONNECTIONS

FOR DETAILS

4GR

8000

2800

5000

7800

3 X WIRES

NEUTRAL

PHASE

GROUND

1 X YELLOW & GREEN

1 X BLUE
1 X BROWN

POWER CORD:

WARNING

AC220V/60Hz

AC208-240/60Hz

AC380/50Hz

AC220V/60Hz

AC208-240/60Hz

AC380/50Hz

25-29

30,5

33-39

Summary of Contents for Linea PB

































































Search results

Summary of Contents for Linea PB

Reviews:

Related manuals for Linea PB

Brands by name

Popular brands

La Marzocco Linea PB, Operating Manual

Search results

Summary of Contents for Linea PB

Reviews:

Related manuals for Linea PB

Brands by name

Popular brands