La Marzocco Linea PB Operating Manual Download Page 25

Page: 25 / 64

Display

Operating Procedure

Description

Programming Mode

When the espresso machine is turned on, press and hold the T3 button

to access the “Barista” programming. After

about 5 seconds the following screen is displayed.

Press the T3 button

to enter the doses programming procedure.

Press the T3 button

to start the doses programming procedure.

To program the coffee brewing time, press the dose button to start and then press it again to stop, once the desired dose

is achieved. Successful programming is indicated by the lighting of the button. This operation must be repeated for each

button whose dose you want to set. The buttons can be programmed in any sequence.

Press the T3 button

to return to the doses programming.

• This parameter allows the operator to

program the amount of coffee (brewing

amount) for each button on the keyboard.

• The brewing amount can be set in terms of

time (sec. ) or pulses. This number refers to

the number of pulses that the flowmeter

sends to the CPU.

• Once programmed, the button remains

lighted.

“Barista” Programming

2
3
4

Group Dose

Settings

Group Dose

Settings

LaMarzocco 00:00

CB 93.8

C SB

Program Dose

Press b To Stop

10 pulses

Press Enter

To Exit

G1B1 Saved

10 Pulses

Program

Volume Dose

Press Enter

To Exit

Summary of Contents for Linea PB

































































Search results

Summary of Contents for Linea PB

Reviews:

Related manuals for Linea PB

Brands by name

Popular brands

La Marzocco Linea PB, Operating Manual

Search results

Summary of Contents for Linea PB

Reviews:

Related manuals for Linea PB

Brands by name

Popular brands