La Marzocco Linea PB Operating Manual Download Page 38

Page: 38 / 64

Display

Operating Procedure

Description

Programming Mode

Press T1

or T2

until the display shows the exit menu, press the T3 button

to return to the “Barista”

programming.

Press T1

or T2

to continue with the programming of the other parameters.

Press T2

and T3

at the same time to exit the programming mode and return to the normal use of the espresso

machine.

• This parameter allows the operator to

program the amount of coffee (brewing

amount) for each button on the keyboard.

• The brewing amount can be set in terms of

time (sec. ) or pulses. This number refers to

the number of pulses that the flowmeter

sends to the CPU.

• Once programmed, the button remains

lighted.

7
8

Group Dose

Settings

Group Dose

Exit

Program Dose

LaMarzocco 00:00

CB 93.8

C SB

“Technical” Programming

Summary of Contents for Linea PB

































































Search results

Summary of Contents for Linea PB

Reviews:

Related manuals for Linea PB

Brands by name

Popular brands

La Marzocco Linea PB, Operating Manual

Search results

Summary of Contents for Linea PB

Reviews:

Related manuals for Linea PB

Brands by name

Popular brands