KYOWA MRS-100 Series Instruction Manual Download Page 10

Page: 10 / 81

EUROPEAN UNION

Hereby, Kyowa Electronic Instruments Co., Ltd., declares that each equipment of the MRS-100 series

is in compliance with Directive 2014/53/EU in countries of the European Economic Area (EEA) and

EFTA countries (Iceland, Norway, Liechtenstein, Switzerland) and Turkey.

English

This equipment is in complience with the essential requirements and other

relevant provisions of Directive 2014/53/EU.

Česky

[Czech]

Toto zařízení je v souladu se základními požadavky a ostatními odpovídajícími

ustanoveními Smérnice 2014/53/EU.

Deutsch

[German]

Dieses Gerät entspricht den grundlegenden Anforderungen und den weiteren

entsprecheneden Vorgaben der Richtlinie 2014/53/EU.

Español

[Spain]

Este equipo cumple con los requisitos esenciales asi como con otras

disposiciones de la Directive 2014/53/UE.

Français

[France]

Cet appareil est conforme aux exigencies essentialles et aux autres dispositions

pertinantes de la Directive 2014/53/UE.

Ελληυική

[Greek]

Αυτός ο εξοπλισμός είναι σε συμμόρφωση με τις ουσιώδεις απαιτήσεις και
άλλες σχετικές διατάξεις της Οδηγίας 2014/53/EE

Italiano

[Italian]

Questo apparato é conforme ai requisiti essenziali ed agli altri principi sanciti

dalla Direttiva 2014/53/UE.

Magyar

[Hungarian]

Ez a készülék teljesíti az alapvet

követelményeket és más 2014/53/EU

irányelvben meghatározott vonatkozó rendelkezéseket.

Nederlands

[Dutch]

Dit apparaat voldoet aan de essentiele eisen en andere van toepassing zijnde

bepalingen van de Richtlijn 2014/53/EU.

Norsk

[Norwegian]

Dette utstyret er i samsvar med de grunnleggende krav og andre relevante

bestemmelser i EU-directiv 2014/53/EU.

Român

[Romanian]

Acest echipament este in conformitate cu cerintele esentiale si cu alte prevederi

relevante ale Directivei 2014/53/UE.

Slovensky

[Slovak]

Toto zariadenie je v zhode so základnými požiadavkami a inými príslušnými
nariadeniami direktív: 2014/53/EU.

Suomi

[Finnish]

Tämä laite täyttää direktiivin 2014/53/EU olennaiset vaatimukset ja on siinä

asetettujen muiden laitetta koskevien määräysten mukainen.

Svenska

[Swedish]

Denna utrustning är i överensstämmelse med de väsentliga kraven och andra

relevanta bestämmelser i Direktiv 2014/53/EU.

The full declaration of conformity for this product can be found at

http://www.kyowa-ei.com/eng/company/environment/eu_declaration.html

The maximum RF power is below:

The band 2405 - 2480 MHz is 4.0dBm

When mounting the product in customersr systems, it is required to proceed additional certification

processes before placing on the market in EU member states to make customers products fully comply

with relative EU standards.

Kyowa can provide a test report of conducted measurement portion for the radio module to customers.

Customers can utilize the test report for the certification processes of own systems as it requires radio.

NOTE

Summary of Contents for MRS-100 Series


















































































Search results

Summary of Contents for MRS-100 Series

Reviews:

Related manuals for MRS-100 Series

Brands by name

Popular brands

KYOWA MRS-100 Series, Instruction Manual

Search results

Summary of Contents for MRS-100 Series

Reviews:

Related manuals for MRS-100 Series

Brands by name

Popular brands