manualshive.com logo in svg

KYOWA MRS-100 Series, Instruction Manual

The KYOWA MRS-100 Series is an advanced electronic device designed to enhance your productivity. To understand its features and operation, you can easily access the comprehensive Instruction Manual for free download at manualshive.com. This manual provides step-by-step guidance to maximize the potential of your KYOWA MRS-100 Series device.

Share
Download
background image

 

2 

 

This Manual describes hardware operation of the MRS-114A, MRS-104A-S, MRS-101A-S, MRS-101A-SE and the 

MRS-101A-V. 

The instruction manual in other available languages can be found at 

https://www.kyowa-ei.com/eng/support/download/manual/acquisition/index.html

 

 

The following accessories are packed with the MRS-114A. 
When unpacking, check the contents to ensure that all accessories are enclosed. 
 

 

STANDARD ACCESSORIES 

Setting Software (MRS-10B) ································································· 1 (CD-R) 
BNC-BNC cable (U-59) ······································································· 4 
USB cable (N-38) ··············································································· 1 
AC adapter* ····················································································· 1 
Ground wire (P-72) ············································································· 1 
Receiving antenna (W1030) ··································································· 2 
High gain dipole antenna (

DA-DB-05RP-SMA-08) ······································· 2

 

Extension cable for receiving antenna (2m)

 

(E-02) ······································· 2 

Side hole suction cup (55mm) ································································ 2 
Cable tie ·························································································· 2 
Product Warranty ··············································································· 1 

* AC power cable is optional (select according to the country or region of use). 

 

 

OPTIONAL ACCESSORIES 

AC power cable: 

P-38 (Japan), P-39 (U.S.A.), P-40 (India), P-41 (Europe), P-42 (Thailand) 

Small planarantenna (EXT-ANT1) 

Planar diversity antenna (EXT-ANT2) 

Extension cable for receiving antenna (6 m) (E-0)3* 

DC power cable (2m) (P-76) 

*E-03 cannot be used in Europe. 

 

 

 

 

The following accessories are packed with the MRS-104A-S. 

When unpacking, check the contents to ensure that all accessories are enclosed. 

 

 

STANDARD ACCESSORIES 

Fastening bracket ··············································································· 2 
Full-bridge Adapter (ADP-401)*   ··························································· 2 
Power Adapter (ADP-40P)*   ································································· 1 
JCIS10-70 Miniature Screw (M2x4)* ······················································· 3 
Battery holder (AAA cell×2) for checking operation (SBH4211AS) ··················· 1 
ID label ··························································································· 1 
Product Warranty ··············································································· 1 
    *Attached to the transmitter body 

 

 

OPTIONAL ACCESSORIES 

Quarter-bridge 2-wire Adapter (120 ohm) (ADP-402-120)* 
Quarter-bridge 3-wire Adapter (120 ohm) (ADP-403-120)* 

* One adapter is available for 2 channels measurements. 

(Two adapters are required to measure 4 channels.) 

Summary of Contents for MRS-100 Series


















































































Reviews:

No comments

Related manuals for MRS-100 Series

Idexx SediVue Dx User Manual preview
SediVue Dx
Brand: Idexx Pages: 6
IDEAL INDUSTRIES SignalTEK II Quick Reference Manual preview
SignalTEK II
Brand: IDEAL INDUSTRIES Pages: 10
M-system TR30 Instruction Manual preview
TR30
Brand: M-system Pages: 5
Unior 270 A Operating Instructions preview
270 A
Brand: Unior Pages: 2
Vaisala HUMICAP HM70 User Manual preview
HUMICAP HM70
Brand: Vaisala Pages: 83
DAKOTA ULTRASONICS ZX-5 Instruction Manual preview
ZX-5
Brand: DAKOTA ULTRASONICS Pages: 50
Jamar Radar Recorder Quick Start Manual preview
Radar Recorder
Brand: Jamar Pages: 4
Hilti PR 300-HV2S Operating Instructions Manual preview
PR 300-HV2S
Brand: Hilti Pages: 31
Rhosonics SDM Series Manual preview
SDM Series
Brand: Rhosonics Pages: 65
red lion DITAK 8 Manual preview
DITAK 8
Brand: red lion Pages: 4
Vega VEGACAP 65 Operating Instructions Manual preview
VEGACAP 65
Brand: Vega Pages: 44
IFM SV0527 Operating Instructions Manual preview
SV0527
Brand: IFM Pages: 17
Chauvin Arnoux C.A 1725 User Manual preview
C.A 1725
Brand: Chauvin Arnoux Pages: 10
sebaKMT Correlux C-3 User Manual preview
Correlux C-3
Brand: sebaKMT Pages: 131
Hammerhead HLMT100 Manual preview
HLMT100
Brand: Hammerhead Pages: 44
b&o LASHINGBITE Instruction Manual preview
LASHINGBITE
Brand: b&o Pages: 32
Dewetron DEWE3-A4L Technical Reference Manual preview
DEWE3-A4L
Brand: Dewetron Pages: 48
Delmhorst J-4 Owner'S Manual preview
J-4
Brand: Delmhorst Pages: 9

Brands by name

Popular brands

Load more brands