KYOWA MRS-100 Series Instruction Manual Download Page 54

Page: 54 / 81

7. Supplementary System Information

7-1. Antenna installation guide

For favorable wireless communication, the orientations and positions where the transmitting and receiving

antennas are installed must be adjusted to prevent a decrease in received signal strength.

Wireless communication is greatly affected by the surrounding environment, such as the presence of obstacles,

influence of reflected waves, and other wireless communication systems. Thus, installation in a suitable

environment is necessary.

Before installing the antennas, refer to the following precautions on setting up the transmitter and receiver.

Install the transmitting and receiving antennas so that there is a direct line of sight between the two units.



In case of the MRS-104A-S



In the case of the MRS-101A-S/V

Obstacle

Poor reception area

Transmission antenna

(Built-in antenna)

Transmitter side

High gain anntena

(Length: 195mm)

Receiver side

Transmission antenna

(Built-in antenna)

Receiving antenna

(Length: 110mm)

Receiver side

Transmitter side

Obstacle

Poor reception area

Summary of Contents for MRS-100 Series


















































































Search results

Summary of Contents for MRS-100 Series

Reviews:

Related manuals for MRS-100 Series

Brands by name

Popular brands

KYOWA MRS-100 Series, Instruction Manual

Search results

Summary of Contents for MRS-100 Series

Reviews:

Related manuals for MRS-100 Series

Brands by name

Popular brands