KYMCO Bet & Win 125 User Manual Download Page 92

Page: 92 / 225

. DRIVE AND DRIVEN PULLEYS/

KICK STARTER

8-8

Bet & Win 125/150

Install the drive pulley face, washer and drive

face nut.

Hold the drive pulley with the universal

holder and tighten the drive face nut.

Torque

: 49.0

58.5N-m

Universal Holder

CLUTCH/DRIVEN PULLEY

Remove the left crankcase cover. (

8-3)

Remove the drive pulley and drive belt. (

Hold the clutch outer with the universal

holder and remove the clutch outer nut.

Universal Holder
Remove the clutch outer.

INSPECTION

Inspect the clutch outer for wear or damage.

Measure the clutch outer I.D.

Service Limit

: 130.5mm replace if over

Drive Pulley Face

Washer

Special

•

Do not get oil or grease on the

drive belt or drive pulley faces.

＊

Clutch Outer

Drive Face Nut

Drive Pulley

Universal Holder

Summary of Contents for Bet & Win 125


































































































































































































































Search results

Summary of Contents for Bet & Win 125

Reviews:

KYMCO Bet & Win 125, User Manual, Page: 92 / 225

Search results

Summary of Contents for Bet & Win 125

Reviews: