KYMCO Bet & Win 125 User Manual Download Page 190

Page: 190 / 225

. REAR BRAKE/REAR FORK/REAR

WHEEL/REAR SHOCK ABSORBER

15-5

Bet & Win 125/150

INSTALLATION

The installation sequence is the reverse of

removal.

Torque

Rear shock absorber lower mount bolt:

19.6

29.4N-m

Rear axle nut: 78.4

98N-m

ADJUSTABLE REAR CUSHION

To suit scooter behaviour to load condition

rear cushion could be adjusted in spring

prelocad.

It is possible to adjust rear cushion in three

positions:
A position “soft”
B position “medium”
C position “hard”
When you adjust rear cushion, the spring

preload of rear cushions must be the same.

REAR SHOCK ABSORBER

REMOVAL

Remove the rear carrier and hand rail. (

2-3)

Remove the met-in box. (

2-3)

Remove the two air cleaner bolts.

Remove the rear shock absorber upper mount

bolt.

Remove the right/left rear shock absorber

upper and lower mount bolts.

Remove the right and left rear shock

absorbers.

DISASSEMBLY

Disassemble the right and left rear shock

absorbers using the rear shock absorber

remover.

Shock Absorber Lower Mount Bolt

Axle Nut

Lower Mount Bolts

Upper Mount Bolts

Brake Caliper Bolts

Rear Shock Absorber Remover

Summary of Contents for Bet & Win 125


































































































































































































































Search results

Summary of Contents for Bet & Win 125

Reviews:

KYMCO Bet & Win 125, User Manual, Page: 190 / 225

Search results

Summary of Contents for Bet & Win 125

Reviews: