KYMCO Bet & Win 125 User Manual Download Page 178

Page: 178 / 225

14.STEERING HANDLEBAR/FRONT WHEEL/FRONT

BRAKE/FRONT SHOCK ABSORBER/FRONT FORK

14-12

Bet & Win 125/150

Check the piston for scratches or wear.

Measure the piston O.D. with a micrometer

gauge.

Service Limit

: 25.30mm

Check the caliper cylinder for scratches or

wear and measure the cylinder bore.

Service Limit

: 25.45mm

ASSEMBLY
Clean all removed parts.

Apply silicon grease to the piston and oil

seal. Lubricate the brake caliper cylinder

inside wall with brake fluid.

Install the brake caliper piston with grooved

side facing out.

Wipe off excessive brake fluid with a clean

shop towel. Apply silicon grease to the

brake caliper seat pin and caliper inside.

Install the brake caliper seat.

INSTALLATION
Install the brake caliper to the shock absorber

and tighten the two bolts.

Torque

: 24.5

34.3N-m

When installing the brake caliper, be sure

to position the brake disk between the

two brake pads.

＊

Install the piston with its outer end

protruding 3

5mm beyond the brake

caliper.

＊

Brake Caliper

Summary of Contents for Bet & Win 125


































































































































































































































Search results

Summary of Contents for Bet & Win 125

Reviews:

KYMCO Bet & Win 125, User Manual, Page: 178 / 225

Search results

Summary of Contents for Bet & Win 125

Reviews: