KYMCO Bet & Win 125 User Manual Download Page 161

Page: 161 / 225

. FUEL SYSTEM/CARBURETOR/

FUEL PUMP/ FUEL TANK

13-17

Bet & Win 125/150

Check the heater with battery.
If the heater is getting hot, means the heater

without problem, otherwise the heater has to

be changed.

CARBURETOR INSTALLATION

Tighten the drain screw.

Install the carburetor onto the intake

manifold and tighten the band.

Install the air cleaner connecting tube and

tighten the band.

Connect the throttle cable to the carburetor.

Connect the auto bystarter wire.

Connect the fuel tube and vacuum tube to

the carburetor.

Perform the following inspections and

adjustments:

•

Throttle grip free play (

3-3)

•

Idle speed (

3-6)

Install the seat, met-in box and frame center

cover.

Auto Bystarter Wire

Fuel Tube

Intake Manifold Band

Air Cleaner Connecting

Tube Band

Heater

•

After connecting the throttle cable,

adjust the throttle grip free play to

6mm.

＊

Throttle Cable

Summary of Contents for Bet & Win 125


































































































































































































































Search results

Summary of Contents for Bet & Win 125

Reviews:

KYMCO Bet & Win 125, User Manual, Page: 161 / 225

Search results

Summary of Contents for Bet & Win 125

Reviews: