KYMCO Bet & Win 125 User Manual Download Page 203

Page: 203 / 225

. IGNITION SYSTEM

17-3

Bet & Win 125/150

SPARK PLUG

For spark plug inspection and adjustment,

refer to page 3-5.

IGNITION COIL INSPECTION

Remove the seat and met-in box. (

2-3)

Remove the ignition coil

IGNITION COIL CONTINUITY TEST

Inspect the continuity of the ignition coil,

primary coil and secondary coil.

Measure the ignition coil resistances at

℃

SECONDARY COIL WITH PLUG CAP

Primary coil

0.16

Secondary coil

without plug cap

3.4

4.6K

Secondary coil with

plug cap

7.6

9.6K

SECONDARY COIL WITHOUT PLUG

CAP

Ignition Coil

AC 110V

This is a general test. Accurate ignition

coil test must be performed with a CDI

tester.

＊

Ignition Coil

Secondary Coil

Primary Coil

Ignition Coil

Summary of Contents for Bet & Win 125


































































































































































































































Search results

Summary of Contents for Bet & Win 125

Reviews:

KYMCO Bet & Win 125, User Manual, Page: 203 / 225

Search results

Summary of Contents for Bet & Win 125

Reviews: