KYMCO Bet & Win 125 User Manual Download Page 88

Page: 88 / 225

. DRIVE AND DRIVEN PULLEYS/

KICK STARTER

8-4

Bet & Win 125/150

Install the drive belt air tube and tighten the

tube band screw.

DRIVE PULLEY

REMOVAL

Remove the left crankcase cover.

Hold the drive pulley using an universal

holder and remove the drive face nut and

washer.

Remove the drive pulley face.

Universal Holder

Remove the drive belt from the movable drive

face.

INSPECTION

Check the drive belt for cracks, separation or

abnormal or excessive wear.

Measure the drive belt width.

Service Limit

: 17.5mm replace if below

Drive Pulley Face

Universal Holder

•

Use specified genuine parts for

replacement.

＊

Movable Drive Face

Drive Belt

Tube Band Screw

Special

Summary of Contents for Bet & Win 125


































































































































































































































Search results

Summary of Contents for Bet & Win 125

Reviews:

KYMCO Bet & Win 125, User Manual, Page: 88 / 225

Search results

Summary of Contents for Bet & Win 125

Reviews: