manualshive.com logo in svg

KYMCO Bet & Win 125, User Manual, Page: 184 / 225

Share
Download
KYMCO Bet & Win 125 User Manual Download Page 184

14.STEERING HANDLEBAR/FRONT WHEEL/FRONT

BRAKE/FRONT SHOCK ABSORBER/FRONT FORK

14-18

Bet & Win 125/150

Drive in new ball races.

INSTALLATION

Apply grease to the top and bottom ball races

and install 26 steel balls on the top ball race

and 19 steel balls on the bottom ball race.

Then, install the front fork.

Apply grease to the top cone race and install

it.

Tighten the top cone race and then turn the

steering stem right and left several times to

make steel balls contact each other closely.

Install the steering stem lock nut and tighten

it while holding the top cone race.

Torque

: 78.4

_

117.6N-m

Install the front wheel. (

!

14-7)

Install the front brake caliper. (

!

14-12)

Install the front inner fender. (

!

2-6)

Install the throttle grip and the right and left

handlebar switches.(

!

14-5)

Install the right and left brake master

cylinders. (

!

14-5)

Lock  Nut  Wrench

Lock  Nut  Wrench

Top Ball Race

Outer  Driver

Be sure to drive the ball races into place

completely.

＊

Check that the steering stem rotates

freely without vertical play.

＊

Bottom Ball Race

Summary of Contents for Bet & Win 125


































































































































































































































Reviews:

No comments