manualshive.com logo in svg

KYMCO Bet & Win 125, User Manual, Page: 155 / 225

Share
Download
KYMCO Bet & Win 125 User Manual Download Page 155

13

. FUEL SYSTEM/CARBURETOR/

FUEL PUMP/ FUEL TANK

13-11

Bet & Win 125/150

AUTO BYSTARTER INSPECTION

/REMOVAL

AUTO BYSTARTER INSPECTION

Measure the resistance between the auto

bystarter wire terminals.

Resistance

:

10

W

 (10 minutes minimum

after 

stopping the engine)

If the reading is not within the limit, replace

the auto bystarter with a new one.

Connect a hose to the fuel enriching circuit

of the carburetor.  Connect the auto

bystarter yellow wire to the positive (+)

terminal of a battery and green wire to the

negative (-) terminal.  Wait 5 minutes and

blow the hose with mouth.  If the passage is

blocked, the auto bystarter is normal.

Disconnect the auto bystarter from the

battery.  Wait 30 minutes and blow the hose

with mouth..  If air can be blown into the

hose, the auto bystarter is normal.

AUTO BYSTARTER REMOVAL

Remove the two set plate screws and set

plate and then remove the auto bystarter

from the carburetor body.

Auto  Bystarter

Hose

Yellow

Screws

Set  Plate

Green

Summary of Contents for Bet & Win 125


































































































































































































































Reviews:

No comments