KYMCO Bet & Win 125 User Manual Download Page 130

Page: 130 / 225

. COOLING SYSTEM

12-4

Bet & Win 125/150

COOLING SYSTEM TESTING

RADIATOR CAP INSPECTION

Install the radiator cap onto the radiator

tester and apply specified pressure to it. It

must hold specified pressure for at least six

seconds.

Radiator Cap Relief Pressure:

0.9

0.15kg/cm

Install the radiator tester onto the radiator

and apply specified pressure to it. It must

hold specified pressure for at least six

seconds.

Check the water hoses and connectors for

leaks.

RADIATOR

RADIATOR INSPECTION

Remove the front upper cover. (

2-5)

Remove the front lower cover. (

2-5)

Radiator Cap

Radiator Tester

The test pressure should not exceed 1.05

kg/cm

. Excessive pressure can damage

the radiator and its hose connectors.

＊

Apply water to the cap sealing surface

before testing.

＊

Summary of Contents for Bet & Win 125


































































































































































































































Search results

Summary of Contents for Bet & Win 125

Reviews:

KYMCO Bet & Win 125, User Manual, Page: 130 / 225

Search results

Summary of Contents for Bet & Win 125

Reviews: