KYMCO Bet & Win 125 User Manual Download Page 36

Page: 36 / 225

. EXHAUST MUFFLER/FRAME COVERS

2-5

Bet & Win 125/150

FRONT UPPER COVER REMOVAL

Remove the four screws on the front upper

cover.

Remove the four screws on the back of the

front upper cover.

Remove the front upper cover.

The installation sequence is the reverse of

removal.

FRONT LOWER COVER REMOVAL

First remove the front upper cover.

Remove the two screws attaching the front

lower cover.

Remove the four screws on the back of the

front lower cover.

Disconnect the right/left turn signal light wire

connectors.

Remove the front lower cover

The installation sequence is the reverse of

removal.

BACK COVER REMOVAL

Remove the front cover.

Remove the key moldings.

Remove the fuel cap moldings.

Remove the back cover bolt.

Remove the fuel tank inlet tube join.

Remove the fuel tank breather tube join.

Remove the back cover.

Screws

Bolt

Key Moldings

Screw

Screws

Fuel Cap Moldings

Fuel Tank Inlet Tube

Fuel Tank Breather Tube

Summary of Contents for Bet & Win 125


































































































































































































































Search results

Summary of Contents for Bet & Win 125

Reviews:

KYMCO Bet & Win 125, User Manual, Page: 36 / 225

Search results

Summary of Contents for Bet & Win 125

Reviews: