KYMCO Bet & Win 125 User Manual Download Page 141

Page: 141 / 225

. COOLING SYSTEM

12-15

Bet & Win 125/150

THERMOSENSOR

THERMOSENSOR REMOVAL

Remove the seat, met-in box and center

cover.

Drain the coolant.

Disconnect the thermosensor wire.

Remove the thermosensor.

THERMOSENSOR INSPECTION

Suspend the thermosensor in a pan of water

over a burner and measure the resistance

through the sensor as the water heats up.

Temperature(

℃

)

100 120

Resistance(

)

154

THERMOSENSOR INSTALLATION

Apply 3-BOND No. 1212 sealant or

equivalent to the thermosensor threads and

install it into the thermostat housing.

Connect the thermosensor wire.

Fill the radiator with coolant. (

3-9)

Install the center cover, met-in box and seat.

(

2-3)

Be sure to bleed air from the cooling

system.

＊

Thermosensor

Thermosensor Wire

Thermosensor

Thermosensor Wire

Thermosensor

Thermometer

Summary of Contents for Bet & Win 125


































































































































































































































Search results

Summary of Contents for Bet & Win 125

Reviews:

KYMCO Bet & Win 125, User Manual, Page: 141 / 225

Search results

Summary of Contents for Bet & Win 125

Reviews: