KYMCO Bet & Win 125 User Manual Download Page 60

Page: 60 / 225

5. ENGINE REMOVAL/INSTALLATION

5-3

Bet & Win 125/150

ENGINE REMOVAL

Disconnect the battery negative cable.

Remove the frame body cover. (

2-3)

Disconnect the engine negative cable.

Disconnect all of the A.C. generator, auto

bystarter, spark plug, thermosensor wire

couplers and connectors.

Disconnect the engine fuel tube.

Drain the coolant. (

3-9)

Disconnect the water hose.

Disconnect the starter motor wire that goes to

the starter relay.

Disconnect the fuel tube and vacuum tube

that go to the carburetor from the fuel pump.

Disconnect the vacuum tube from the air cut-

off valve (ACV).

Disconnect the throttle cable from the

carburetor.

Remove the brake fluid tube bolt of the rear

brake caliper.

Remove the rear brake caliper bolt and the

rear brake caliper.

Starter Relay

Wire Connectors

Rear Brake Caliper

ACV Vacuum Tube

Fuel Tube

Throttle Cable

Fuel Pump Vacuum Tube

Brake Fluid Tube

Rear Brake Caliper

Summary of Contents for Bet & Win 125


































































































































































































































Search results

Summary of Contents for Bet & Win 125

Reviews:

KYMCO Bet & Win 125, User Manual, Page: 60 / 225

Search results

Summary of Contents for Bet & Win 125

Reviews: