KYMCO Bet & Win 125 User Manual Download Page 170

Page: 170 / 225

14.STEERING HANDLEBAR/FRONT WHEEL/FRONT

BRAKE/FRONT SHOCK ABSORBER/FRONT FORK

14-4

Bet & Win 125/150

STEERING HANDLEBAR

REMOVAL

Remove the handlebar front and rear covers.

(

2-6)

Remove the front and rear brake master

cylinder attaching bolts.

Remove the front upper cover. (

2-5)

Remove the front lower cover. (

2-5)

Remove the floor board. (

2-4)

Remove the leg shield. (

2-5)

Remove the four screws attaching the right

and left handlebar switches.

Disconnect the throttle cable from the throttle

grip and remove the throttle grip from the

handlebar.

Remove the handlebar lock nut and take out

the bolt.

Remove the handlebar.

INSTALLATION

Install the handlebar onto the steering stem

and install the handlebar collar, lock nut and

bolt.

Tighten the bolt to the specified torque.

Torque

: 39.2

49N-m

Brake Master Cylinders

Screws

Bolts

Collar

Throttle Grip

Throttle Cable

Bolt

Lock Nut

Summary of Contents for Bet & Win 125


































































































































































































































Search results

Summary of Contents for Bet & Win 125

Reviews:

KYMCO Bet & Win 125, User Manual, Page: 170 / 225

Search results

Summary of Contents for Bet & Win 125

Reviews: