Kverneland TS-T Service Manual Download

Page: 61 / 94

Default:

• Calibrate sensor

• 0

• Calibrate sensor

Default:

• DZ

10 4

• axle gnl,gnr

0.70

• Ikarus S gnl,gnr +0.05
• Ixtrack gnl,gnr

-0.05

Defaultr:

Calibrate the Limit

Δ D Axle 50 cm

Δ D Drawbar 0 cm

Parameter:

Information (screen only
visible when connected

Default:

Explanation screen:

• Front sensor
• (always 0)
• Rear sensor

Explanation screen

See chapter 4.10

Explanation screen:

See chapter 4.10

Explanation screen:

Software version ASV
pilotbox

Explanation screen:

For entering the factory
setting enter OK

Default:

Explanation screen:

Entering the factory settings

Default:

Fill in the right parameters

Default:

Fill in the right parameters
Depending on the machine
configuration.

Explanation screen:

• number of sections
• Main Valve yes/no
• Border nozzle yes/no

Explanation screen:

SW= machine hydraulic
configuration
RP = oil circulation Yes/No

4.2

FMC-R screen information including parameters

Summary of Contents for TS-T































































































Search results

Summary of Contents for TS-T

Reviews:

Related manuals for TS-T

Brands by name

Popular brands

Kverneland TS-T, Service Manual

Search results

Summary of Contents for TS-T

Reviews:

Related manuals for TS-T

Brands by name

Popular brands