Kverneland 2316M Technical & Service Manual Download | Manualshive

Page: 58 / 60

background image

8.0 Options

Chain for locking the lift arms

Quick release of knives

Quick release of knives

Chain for locking the lift arms

•

The machine can be fitted
with knife quick release, so
the knives can easily be
changed or turned in just a
few seconds with the help of a
simple tool.

•

The machine can be equipped
with a chain to prevent the
tractor's lift arms from
lowering. The chain is fitted
between the highest point on
the tractor and one of the lift
arms.

58

«
...
56
57
58
59
60
»

Summary of Contents for 2316M





























































Reviews:

No comments

Related manuals for 2316M

Brand: Laica Pages: 4

Brand: Keithley Pages: 42

Brand: NCR Pages: 20

Brand: DARAY Pages: 32

Body Armor Night Splint

Brand: Darco Pages: 2

Brand: MacDon Pages: 74

Brand: R.M. Young Pages: 10

Brand: LA Audio Pages: 9

Brand: PASCO Pages: 30

Brand: XFit Pages: 16

BlackBox Series

Brand: Nakamichi Pages: 23

Brand: Harken Pages: 4

Brand: Abbriata Pages: 27

Brand: A&D Pages: 33

Brand: Mac Medical Pages: 23

ABS-Lock III-BE

Brand: ABS Pages: 8

Brand: ZAMST Pages: 14

Brand: Future Artist Pages: 42

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands