Kverneland 2316M Technical & Service Manual Download Page 48

Page: 48 / 60

Cutter bar repair

Assembly of bearing house(s)

Cutter bar repair

Assembly of bearing house(s)

Cutter bar repair

Assembly of intermediate
gearwheel

Cutter bar repair

Assembly of intermediate
gearwheel

•

The lock bolt is provide with
LOCTITE 242 when fitted in
the shaft.

•

Tighten the lock bolts to 90
Nm / 66 ft.lbs. by use of a
torque wrench.

•

Use a nylon hammer and hit
the shaft on top and re-torque
the bolt again.

•

All the special nuts is provided
with new O-rings.

•

Force the edge of the plate up
a bit by use of tool T7.

•

Carefully place all the special
nuts in the cutter bar as
shown.

NB!

Do not damage the O-rings

when the special nuts is
placed in the cutter bar.

•

Guide the end cap in to the
cutter bar as shown.

•

Tighten the end cap.

NB!

Always use a new gasket

when the end cap is fitted.

•

Place tool T6 as shown.

•

The special nuts in the cutter
bar is been kept in place by
using tool T6.

5.4.2 Cutter bar – repair instructions

Summary of Contents for 2316M





























































Search results

Summary of Contents for 2316M

Reviews:

Related manuals for 2316M

Brands by name

Popular brands

Kverneland 2316M, Technical & Service Manual

Search results

Summary of Contents for 2316M

Reviews:

Related manuals for 2316M

Brands by name

Popular brands