ME5700, WSM
FRONT AXLE
6-S16
Backlash and Tooth Contact between Bevel Pinion Shaft and
Bevel Gear
1. Set a dial indicator (lever type) with its finger on the tooth
surface.
2. Measure the backlash by fixing the bevel pinion shaft (3) and
moving the bevel gear (1) by hand.
3. If the backlash exceeds the allowable limit, adjust with the
shim (4).
4. Adjust the backlash properly by repeating the above
procedures.
5. Apply red lead lightly over several teeth at three positions
equally spaced on the bevel gear (1).
6. Turn the bevel pinion shaft (3), while pressing a wooden piece
against the periphery of the bevel gear.
7. Check the tooth contact. If not proper, adjust according to the
instructions shown in the figure.
(Reference)
A
Thickness of adjusting collar (2) :
A
Thickness of adjusting shims (4)
A
After adjusting the tooth contact, check the backlash
between spiral bevel pinion shaft and spiral bevel gear
again.
Backlash between bevel
gear and bevel pinion
shaft
Factory spec.
0.20 to 0.30 mm
0.0079 to 0.0118 in.
Allowable limit
0.40 mm
0.0157 in.
5.8 mm (0.228 in.)
6.2 mm (0.244 in.)
5.9 mm (0.232 in.)
6.4 mm (0.252 in.)
6.0 mm (0.236 in.)
10.0 mm (0.394 in.)
6.1 mm (0.240 in.)
1.6 mm (0.063 in.)
2.2 mm (0.087 in.)
1.8 mm (0.071 in.)
2.4 mm (0.094 in.)
2.0 mm (0.079 in.)
(1)
Bevel Gear
(A)
Proper Contact :
(2)
Collar
More than 35 % red lead
(3)
Bevel Pinion Shaft
contact area on the gear
(4)
Shim
tooth surface. The center of
The center of tooth contact at
1/3 of the entire width from
the small end.
(B)
Deep Contact :
Decrease the shims.
(C)
Shallow Contact :
Increase the shims.
0000001927E
KiSC issued 04, 2006 A
Summary of Contents for ME5700
