background image

GENERAL PRECAUTIONS

39

2.2 GENERAL PRECAUTIONS

2.2.1 GENERAL SAFETY RULES

q

Only trained and authorized staff can use the machine and perform maintenance operations.

q

Follow all the safety rules, precautions and instructions when using the machine or performing maintenance op-
erations.

q

When working with other operators or when the work site is often occupied by other operators, make sure that 
everyone knows and understands all the agreed signals and, in any case, that everyone works in such a way as 
to be able to see the machine and to be visible to the operator.

2.2.2 HOW TO BEHAVE IN CASE OF ANOMALIES

q

If anomalies are observed while the machine is working or is being serviced (noise, vibrations, bad smells, incor-
rect  measures,  smoke,  oil  leakages,  or  any  other  anomaly  indicated  by  the  warning  devices  or  the  warning 
lights), inform the staff in charge, so that the necessary measures can be taken. Do not use the machine until 
such anomalies have been eliminated.

2.2.3 SAFETY DEVICES AND GUARDS

q

Make sure that all the guards and covers are in the correct position. Have guards and covers changed or re-
paired if damaged. Neither use the machine without guards, nor remove the guards when the engine is running.

q

Always use the proper safety devices to lock the machine when parking; always fasten the seat belt.

q

Do not remove the safety devices and always keep them in good operating conditions.

q

Any improper use of the safety devices may result in serious injury or even death.

2.2.4 CLOTHING AND PERSONAL PRO-

TECTION ITEMS 

q

Do not wear large or loose clothes, rings and watches, and do 
not approach the machine with loose long hair, since they can 
get entagled in the moving parts of the machine and cause seri-
ous injury or damage.

Avoid also wearing clothes dirty with oil or fuel, since they are 
flammable.

q

Wear a hard hat, goggles, safety shoes, mask, gloves and ear 
muffs when operating the machine or performing maintenance 
operations.

q

Always  wear  safety  goggles,  a  hard  hat  and  heavy  gloves  if 
your  job  involves  scattering  metal  chips  or  minute  materials; 
these  precautions  are  particularly  useful  when  hammering  the 
equipment  connection  pins and  when blowing compressed air 
into the air filter and the radiator.

During these operations, make also sure that no one is standing 
or working near the machine without the necessary protection 
items.

q

When working for 8 hours with a noise level exceeding 90 dBA, 
it is necessary to use headphones or ear plugs and be particu-
larly careful, especially at the end of the work shift.

RKA00510

WEAM012405

Summary of Contents for PC16R-3

































































































































































































































































































Reviews: