manualshive.com logo in svg

Komatsu PC16R-3, Operation & Maintenance Manual

Share
Download
Komatsu PC16R-3 Operation & Maintenance Manual Download Page 223

MAINTENANCE PROCEDURES

221

INSTALLING THE RUBBER TRACKS

1.

Raise the undercarriage using boom and arm and make sure 
that the grease contained in the cylinder has been eliminat-
ed.

Carry out this operation shifting the control levers very slowly.

2.

Install the rubber tracks on the sprocket by fitting the driving 
blocks.

3.

Turn the sprocket (1) as if in reverse, then push the track to-
wards the turret.

4.

Using a steel tube (2), position the track and turn the sprock-
et again.

5.

Make sure that the track is correctly installed on the sprocket 
and the idler roller.

6.

Adjust the track tension. For details, see "4.9.1.g CHECKING 
AND ADJUSTING THE RUBBER TRACK TENSION").

7.

Make sure that the track tension is correct, that the track is 
correctly  fitted  in  the  sprocket  and  the  idler  roller,  then  rest 
the machine on the ground.

RYA05230

RYA05240

RYA05250

WEAM012405

Summary of Contents for PC16R-3

































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands