Komatsu PC16R-3 Page 143 Operation & Maintenance Manual Download

Page: 143 / 288

USE OF THE MACHINE AND RELATED CONTROLS

141

STEERING (CHANGING DIRECTION)

When steering to the left:

If the left travel lever is shifted back to the neutral position, the
machine will steer to the left.

NOTE

To steer to the right, operate the right travel lever in the same
way.

HOW TO CARRY OUT COUNTER-ROTATIONS



(SPIN TURN)

To carry out a counter-rotation to the left, pull the left travel lever
backward and push the right travel lever forward.

NOTE

To carry out a counter-rotation to the right, pull the right travel
lever backward and push the left travel lever forward.

RYA02170

RYA02180

WEAM012405

Summary of Contents for PC16R-3
































































































































































































































































































Search results

Summary of Contents for PC16R-3

Reviews:

Related manuals for PC16R-3

Brands by name

Popular brands

Komatsu PC16R-3, Operation & Maintenance Manual

Search results

Summary of Contents for PC16R-3

Reviews:

Related manuals for PC16R-3

Brands by name

Popular brands