Komatsu PC16R-3 Page 56 Operation & Maintenance Manual Download

Page: 56 / 288

PRECAUTIONS TO BE TAKEN WHEN WORKING

15 - TRAVEL STRAIGHT AHEAD



Rotate the fists vertically indicating the turning direction of the
wheels.

16 - TRAVEL STRAIGHT AHEAD



Rotate the fists vertically indicating the turning direction of the
wheels.

17 - DISTANCE TO BE COVERED



With the hands raised and facing inwards, move the hands
laterally indicating the distance to be covered.

18 - CARRY OUT THE MOVEMENTS SLOWLY



One hand still in front of the hand that indicates the move-
ment to be carried out. (The figure represents the “lift slowly”
control).

19 - STOP



With one arm extended laterally, open the hand facing down-
wards and move the arm forwards and backwards.

20 - EMERGENCY STOP



With both arms extended in horizontal position, open the
hands downwards and move both arms forwards and back-
wards.

RKA15280

RKA15290

RKA15300

RKA15310

RKA15320

RKA15330

WEAM012405

Summary of Contents for PC16R-3
































































































































































































































































































Search results

Summary of Contents for PC16R-3

Reviews:

Related manuals for PC16R-3

Brands by name

Popular brands

Komatsu PC16R-3, Operation & Maintenance Manual

Search results

Summary of Contents for PC16R-3

Reviews:

Related manuals for PC16R-3

Brands by name

Popular brands