manualshive.com logo in svg

Komatsu PC16R-3, Operation & Maintenance Manual

Share
Download
Komatsu PC16R-3 Operation & Maintenance Manual Download Page 149

USE OF THE MACHINE AND RELATED CONTROLS

147

q

OPERATIONS  FOR  WHICH  IT  IS  NOT  ALLOWED  TO  EX-
PLOIT THE DROPPING FORCE OF THE BUCKET

Do  not  exploit  the  dropping  force  of  the  bucket  to  use  it  as  a 
pickaxe, breaker, or pile driver.

This may considerably reduce the life of the machine.

q

OPERATIONS  FOR  WHICH  IT  IS  NOT  ALLOWED  TO  EX-
PLOIT THE FORCE OF GRAVITY OF THE MACHINE

Do not use the force of gravity of the machine to carry out dig-
ging operations.

When working on hard rocky surfaces, use some other method 
to  break  the  rock  into  small  pieces  before  excavating.  This 
avoids any damage to the machine and is also more economi-
cal.

q

SUPPORT  THE  MACHINE  WITH  BOTH  SIDES  OF  THE 
BLADE

When  using  the  blade  as  a  stabilizer,  avoid  loading  all  the 
weight of the machine on one side of the blade only.

RYA02400

RYA02410

RYA02440

WEAM012405

Summary of Contents for PC16R-3

































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands