background image

PRECAUTIONS TO BE TAKEN BEFORE STARTING THE ENGINE

48

2.3 PRECAUTIONS TO BE TAKEN BEFORE STARTING THE 

ENGINE

2.3.1 SAFETY AT THE WORK SITE

q

Before  starting  the  engine,  thoroughly  check  the  area  for  any 
unusual condition of the ground due to which work may be dan-
gerous.

q

Check the conditions of the ground at the work site and before 
starting the engine define the work plan and the best and safest 
operating procedure.

q

Make  the  ground  surface  as  level  as  possible  before  carrying 
out any operation.

q

In  case  of  work  on  the  road,  protect  pedestrians  and  cars  by 
designating a person for work site traffic duty and install fences 
around the work site.

q

If water lines, gas lines, and telephone or high-voltage electric 
lines are located under the work site, contact the relevant utility 
company  in  order  to  find  out  their  exact  positions  or  to  make 
them ineffective until the end of the operations. Be careful not to 
sever or damage any of these lines.

q

Check the depth and flow of water before operating in water or 
on river banks.

2.3.2 FIRE PREVENTION 

q

Completely remove any wood chips, rubbish, paper and  other 
flammable materials that may have accumulated inside the en-
gine compartment, since they may cause fires.

q

Check the fuel and hydraulic system pipes for leaks and if nec-
essary repair them. Wipe up any excess oil, fuel or flammable 
fluids.

q

Make sure that fire extinguishers are available in the work area.

2.3.3 PRECAUTIONS CONCERNING THE OPERATOR SEAT

q

Do not leave objects or tools lying around inside the cab. They may hinder the operation of the controls and 
cause serious accidents.

q

Keep the cab floor and the controls (pedals and levers) clean, by removing any trace of oil and grease and, as 
far as the floor is concerned, remove any excess dirt (earth, stones, etc.).

q

Check the seat belt and change it if it is broken or damaged.

Replace any component only with homologated parts available at Komatsu or its Distributors.

RWA00220

RKA00430

WEAM012405

Summary of Contents for PC16R-3

































































































































































































































































































Reviews: